Drill Rod - Drill PipeFor Horizontal Directional Drilling and Boring

Drill Pipe Manufacturing Processes | TuffRod

At TuffRod we understand that having the right information to make an informed decision when buying a bore pipe is of the essence and want our customers to understand the manufacturing methods that we use.

We utilize the three most common manufacturing methods for Horizontal Directional Drill Pipe, 1-Piece Forged, Inertia Welded, and Press Fit & Welded.

Below is an explanation of how drill pipe is manufactured using each of the methods to provide you with a better understanding.

1-Piece Internal & External (IEU) Forged Drill Pipe

An IEU integral forged or 1-Piece forged drill pipe is made up solely from one piece of material. This pipe has the same chemical makeup for the threaded connections and the mid-body tube with no weld zone between them.

The raw material, or green tube, is saw cut to an exact calculated length to ensure proper finished length tolerances. The ends of the green tube are then heated to produce a workable material for the forging or upsetting process.

The upsetting process forms the steel to create the desired outside diameter, inside diameter and tong length required for the pin and box connection.

The next step is to heat-treat the entire tube to a specified grade or hardness. After the tube has been heat treated and straightened, the upset ends are precision machined and threaded.

Final inspection is the last and most crucial step.

Inertia Welded Drill Pipe

Inertia welded drill pipe is similar to the integral drill pipe in that the green tube is saw cut to length; upsets are forged on each end to form a thicker wall dimension, which creates a larger weld surface. With more cross-sectional area, there is more strength to that weld area.

The main difference with the inertia welded drill pipe is that it is manufactured from three separate pieces.
 
  • Mid-Body Tube
  • 2 Threaded Connections
  • Tool Joints
The tool joints are commonly made up from alloy bar stock. After the bar stock has been saw cut to length, drilled and machined, they are heat treated to a specified hardness.
After heat-treat, the tool joints go through a final machining, threading and inspection process. The next step is the inertia welding process.

The welding process is a solid-state welding technique that forges metal together without causing a melt to occur. Because there is no melt product produced during the inertia weld, there is no recast metal or grain enlargement after the weld is complete.

The mid-body tube is held stationary by hydraulic clamps, and the threaded tool joint is clamped in a collet chuck on a rotatable spindle. A flywheel is also attached to the spindle at a pre-calculated weight.

The weld cycle consists of accelerating the spindle to a predetermined speed, which is controlled electronically to shut off the drive system when the set speed is reached. This allows the mass of the rotating tool joint and spindle to be free and spinning by kinetic energy alone. At the precise time, the machine forces the tool joint and tube together causing friction at the weld interface. The pressure is maintained until all of the energy in the rotating spindle has been consumed in the weld, which in turn stops the rotation.

This metal-to-metal fusion creates 100 percent weld penetration. The weld zone is then machined, heat-treated and inspected to ensure proper strength and hardness.

Press Fit & Welded

This process is one of the oldest drill pipe manufacturing processes. The process is quite similar to the inertia welded pipe in that the tool joints are made separately from bar stock and the mid body is forged and machined so the tool joints can be pressed in the forged ends of the tube.

After they are precisely pressed, they go through a MIG welding process. After the pipes are welded, the weld zone is appropriately heat-treated to ensure precise strength and hardness.

Quality Manufactured Drill Pipe

Any of the above manufacturing processes will produce a quality drill pipe. Just like any other product, if you do it right and refrain from any shortcuts, you will put out a quality product.

After choosing a reputable company to purchase your new drill string from, one must be able to maintain it properly to get the most out of his or her's investment.

To learn more about drill pipe manufacturing, contact the HDD drill pipe experts at TuffRodd or call (844)586-9354 today!

 

Back to Top  Contact Us

American Owned & Operated

American Owned & Operated

TuffRod - The Pipe Authority

TuffRod is The Pipe Authority. We know HDD Drill Rod / Pipe like the back of our hand. Please use the search function at the top of the screen to find the right rod for your drill.